close
close

How To Remove A Cast Iron Alcove Tub

Heavy cast iron tubs or bathtubs with tiling surrounds can cost $1,000 or more to remove. However, with the right tools and the correct amount of know how, you will find that this is a task that is not too difficult.


KOHLER Bellwether 60 in. x 30 in. ADA Cast Iron Alcove

One person should lift the front edge of the tub, while another slides a couple of 1 x 4 boards underneath to get it off the floor.

How to remove a cast iron alcove tub. Cut away a horizontal strip of wall about 6 inches above the bathtub to reveal the tub flange, and remove any screws that secure the flange to the wall studs. American standard alcove bathtub best bathtubs alcove tub bathtub. The largest clawfoot tubs can weigh well over 500 pounds when dry and more than 1,000 pounds when filled with water.

Removing your cast iron tub might seem like a daunting task, but if you break it down into smaller steps, it should be relatively straightforward. A cast iron alcove bathtub like a kohler villager weighs approximately 316lbs making it darned near impossible for one person to remove or to install for that matter. Using a putty knife, the technician carved away the caulk caught between the walls and the tub.

You can start the process by using a 2lb sledgehammer on the apron. Remove the front, side, and rear walls of the tub. Cover the cast iron tub with a piece of plywood.

See also  How To Remove Overspray From Car Interior

Unpack the tub, set it upright on the 2×4 boards and slide it all the way into the alcove to make sure it fits. The restoration of the cast iron tub begins. I contact metal scrappers who will haul it out for free.

First, turn off the water at the shutoff valve. He cleaned the bathtub to remove the grime. Unhooking the drain is similar to a sink drain:

Test that the bathtub is level with a spirit level and shim it with metal shims if necessary. I picked up a kohler villager cast iron tub yesterday, which is currently in my garage. When everything checks out, slide the tub all the way out of the alcove.

Slide the tub out of the alcove using the 1 x 4 boards as skids. Be safe and have a helper for these next few steps. The steps taken to give the cast iron tub a new beginning are as follows:

This is important because you don’t want any debris to fall into the tub and crack it as you proceed further into this process. You may need to cut the plywood to make sure it fits snugly above the bathtub. Next, he removed the drain cover and covered the faucets.

A kohler 5ft x 18 was close to 400 pounds. Acrylic is stronger than fiberglass but. Depending on what your plans are for the tub, you have several different methods you can use to remove one.

Even in half, cast iron is heavy. Then, remove the drain from the bottom of the tub, saw the drain pipe off, and remove it too. Typically, the tub is installed in an alcove section of the bathroom with three of its sides enclosed by a wall.

See also  How To Remove Granite Countertops Without Breaking

On the front side, you can place a shower curtain or bathtub door to provide privacy. The low prices for alcove bathtubs sit in the 400 to 500 range. In some cases, structural reinforcement of floors may be necessary if you want to install a large cast iron bathtub.

Cast iron tubs can weigh over 300lbs easily depending on the size, shape, and wall thickness, which makes them very difficult to remove. Hopefully the post content article how to remove an alcove bathtub, what we write can you understand. An alcove bathtub is a tub that is surrounded by three walls.you may find that when it comes to removing this type of tub, it can be a more difficult task than a standalone type of bathtub.

You can use a reciprocating. If you cut the tub in half, just leave the overflow attached. Alcove bathtub enamel cast iron.

If there are any gaps between the tub flange and the studs, this is the last chance to make corrections to the wall framing. Remove any stringer supports left on the wall. It can be cut with angle grinder with metal blade (that method will require dust mask.

Today i searched forums on how to remove a cast iron tub after all answers suggested a sledgehammer, i tried a 4 1/2 inch grinder with a metal cutting blade.to me it proved easier than the sledge idea.its a small bath soon to be 3 foot deeper. The term alcove doesn't refer to the shape or size of the bathtub, but the installation. I've tried both methods in the past so i can help you prepare for what you're in store for.

See also  How To Remove Ceramic Coating From Plastic Trim

So the only way to remove a cast iron tub is in pieces.


60" Rolfe Acrylic Alcove Tub White Bathtubs Bathroom


Vintage Cast Iron Art Deco Alcove Bathtub Antique tub in


Memoirs Alcove 60" x 34" Whirpool Bathtub Soaking


KOHLER Bellwether 60 in. x 30 in. ADA Cast Iron Alcove


Princeton 60" x 30" Alcove Soaking Bathtub Soaking


KOHLER Villager 60 in. RightHand Drain Rectangular Alcove


KOHLER Bellwether 60 in. x 30 in. ADA Cast Iron Alcove


Kohler K7160 White Villager Collection 60" Cast Iron


American Standard Cambridge 60 in. Left Drain Rectangular


Kohler K83847 Bellwether Bath Tub 60" L x 30


Bootz Industries Bootzcast 60 in. Left Drain Rectangular


Refinish Your CastIron Tub Cast iron tub, Cast iron


Full Size Of Walk In Tub Shower Kohler Drop Tubs Archer


KOHLER Bellwether 60 in. x 32 in. ADA Cast Iron Alcove


KOHLER Bellwether 60 in. x 30 in. ADA Cast Iron Alcove


Pin on 922 PROSPECT PLACE


KOHLER Villager 5 ft. Cast Iron RightHand Drain


Cambridge 60" x 32" Alcove Soaking Bathtub in 2020


KOHLER TeaforTwo 5 ft. Reversible Drain DropIn Cast

How To Remove A Cast Iron Alcove Tub

Leave a Reply

Your email address will not be published. Required fields are marked *

Scroll to top